Civil Lab Equipment

Product Details:

MS Compaction Factor Apparatus: Keeping in mind the varied needs of our esteemed clients, we put forward a wide assortment of Compaction Factor Apparatus. Our experts perform a series of check on numerous parameters, in order to guarantee the quality and functioning of this product. Extremely robust and built with quality checked components, this machine is very durable and can withstand even the roughest conditions.

Other Details:

• The compaction factor is defined as the ratio of the mass of the concrete compacted in the compaction factor apparatus to the mass of the fully compacted concrete.
• It involves dropping a volume of concrete from one hopper to another and measuring the volume of concrete in the final hopper to that of a fully compacted volume.
• The results of the compaction factor test can be correlated to slump, although the relationship is not linear.
• This test is difficult to run in the field and is not practical for large aggregates (over 1 inch) Compared to the slump test, the apparatus is bulky and a balance is required to perform measurements.
• The apparatus, consist of a rigid frame that supports two conical hoppers vertically aligned above each other and mounted above a cylinder.
• The top hopper is slightly larger than the bottom hopper, while the cylinder is smaller in volume than both hoppers.
• To perform the test, the top hopper is filled with concrete but not compacted.
• The door on the bottom of the top hopper is opened and the concrete is allowed to drop into the lower hopper.
• Once all of the concrete has fallen from the top hopper, the door on the lower hopper is opened to allow the concrete to fall to the bottom cylinder.
• The excess concrete is carefully struck off the top of the cylinder and the mass of the concrete in the cylinder is recorded.
• This mass is compared to the mass of fully compacted concrete in the same cylinder achieved with hand rodding or vibration. Complete with a trowel and tamping bar 0-60 cms long X 16mm Dia.
  
  

Optional Accessories:

• Concrete Scoop
• Straight Edge
• Weighing Balance

Product Details:

Soil Cone Penetrometer is based on the relationship between moisture content and the penetration of the cone into the soil sample. The moisture content at a given depth of penetration of the cone is taken as the liquid limit. The Automatic Penetrometer (Digital Timer) is supplied complete with a stainless steel penetration test cone 35mm long with a smooth polished surface and an angle of 30° and a Penetration test cup 55mm DIA x 40mm deep. Facility exists for adjusting cone height in relation to the specimen.

Product Details:

Optional Accessories: A Drill rod, 1.5 meter long, one side male thread and the other side female.

Product Details:

The Direct Shear test apparatus consisting of a square or circular box divided into two halves. The specimen, contained in the box, is subjected to a constant normal load while an increasing horizontal force is applied to one of the sections of the shear box. This force causes a shear failure along the juncture between the box sections of this. The shear force and the normal load are measured directly. The rate of strain is adjusted by the speed of the horizontal force applied. The loading unit has V-strips on which the shear box housing rests. The load yoke in these direct shear test apparatus helps counterbalance the loading system. The lead screw connected to the shear box housing helps the application of shear stress.

Direct Shear Test Apparatus comprises of Direct Shear Box assembly for 60mm x 60mm x 25mm thick specimen, Shear Box Housing, Specimen cutter, Loading Unit with a capacity of 8kg/cm2, set of weights to give normal stress of 3kg/cm2, Proving Ring duly calibrated by Nccbm (Govt) of 2.5kN (250kgf) capacity & 2 (Two) Dial Gauges 0.01mm x 25mm travel. The load yoke with direct and through a level system for applying normal load upto 8 kg/cm2 capacity, fixtures for proving ring, brackets for holding consolidation and strain dial gauges are also provided in these direct shear test apparatus.

Product Details:

An extensive range of Rapid Moisture Meter is offering by us to the customers as per IS 2720 (PART II) on 0-25% and 0-50% for quick determination of moisture content of the material in powder forms such as coal pottery slip, soil, sand, cement and many more. Acetylene gas is generated when Calcium carbide comes in contact with moisture. This principle is used in a rapid moisture meter. A perfectly weighed quantity of samples is mixed with a specific quantity of calcium carbide reagent and the whole mixture is thoroughly shaken in a vessel to which a pressure gauge is fixed. The acetylene gas that is produced develops pressure. The instrument specifies moisture on a wet/weight basis and easily convertible to dry weight basis. It consists of a rubber sealing gasket, a pressure vessel with clamp for sealing cap, pressure gauge calibrated in percentage moisture content 0 -25% on a wet weight basis, one bottle of reagent approx. 450 gram, a scoop for measuring carbide reagent, a counted poised balance for weighing the sample, one cleaning brush, steel balls for through mixing and wooden carrying box with handle.

 

Features:

• Innovative technology
• Dimensionally accurate
• Effective results

Product Details:

Relative Density Apparatus is used to determine the relative density of free-draining soils. Soils of this type normally do not respond well to conventional Proctor moisture-density compaction tests. Maximum density is determined by placing soil in special molds and densifying using a vertically vibrating table and surcharge. Minimum index density is determined by loose placement in the molds, using special pouring funnels, scoop, or shovel, depending on size of soil particles.

• Semi-noiseless Vibratory Table has a cushioned steel 30 x 30" (762 x 762 mm) vibrating deck activated by electromagnetic vibrator with over 100 lb (45.5 kg) actuator. The table has 750 lbs (341 kg) load capacity and requires 800 watts, 12 amps at 230 V. Table height is 21" (533 mm). Vibration rate is 3600 VPM (3000 @ 50 Hz) and amplitude adjusts in accordance with ASTM requirements. The solid state circuitry allows precise amplitude control even with fluctuating voltage supplies.
• Cylindrical metal unit weight Mold Sets for 0.1 and 0.5ft3 (2.83 and 14.2 liters) capacity have attached carrying handles and guide brackets for the Gauge Set. They come complete with detachable guide sleeve with clamp assembly, surcharge base plate with removable handle, and surcharge weight and handle. Mold included with Set is 6.000" (152.4 mm) ID x 6.112" (155.2 mm) IH; surcharge weight plus base plate has 56. 5 + 0.5 lb (25.5 + 0.2 kg) total weight. Larger mold with Set is 11.000 (279.4 mm) ID x 9.092" (230.9 mm) IH with 190 + 2 lb (86.2 + 0.9 kg) total weight of base plate with surcharge weight. Model Gauge Set fits guide brackets of either Mold Set to measure distance from top of mold to top of base plate after densification (to compute volume change). Set includes a 2" (50.8 mm) Dial Indicator, travel is 0.001" (0.025 mm), and also a special holder to fit molds. A metal 3 x 12 x 1/8" (76 x 305 x 3.2 mm) calibration bar is also included.
• Accessory Pouring Funnel Set Model is required for loose placement of 3/8" (9.5 mm) and finer soil. Set includes two 6" (152 mm) diameter x 12" (305 mm) long metal cylinders, each with funnel and 6" (152 mm) long delivery spout attached to one end. Spouts are 1" (25.4 mm) and 1/2" (12.7 mm) in diameter.

Product Details:

The Flow Table consists of a brass table top 250 +- 2.5 mm dia, mounted on a rigid stand. The table top is reinforced with equally spaced ribs and allowed to drop through 12mm by a ground and hardened cam. The Motor Drive assembly using the geared motor box is designed to rotate the cam through the shaft at 100 rpm. Complete with Flow mould 1 OOmm base dia, 70mm top dia and 50mm high. The new design has better aesthetics and compact look.

Product Details:

Camber Board is used to check and maintain the slope of the road as per design.

We “Babir Industries” is a Sole Proprietorship based firm, engaged as the foremost Manufacturer and Trader of Civil Lab Equipment and Material Testing Equipments and many more. 

Product Details:

We are one of the leading manufacturers & suppliers of Compaction Factor Apparatus.

Product Details:

Kelley Ball Penetration Apparatus: The apparatus is used to determine the workability of Portland cement concrete. The Kelly Ball test is considered to be simple and much faster than the slump test. Twice the Kelly Ball reading approximately equals the slump.

 

Salient Features :
It consists of a cylinder with a ball-shaped bottom and handle ,together weighing 15 kg. A strip frame, guides the handle and serves as a reference for measuring the depth of penetration. The handle is graduated in MM. Penetration can be recorded to the nearest 0.5mm.

Product Details:

Standard and Modified Compaction Test:

• The apparatus consists one each of compaction mould gun metal/ M.S., 100 mm i. D. X 127. 3 mm height x 1000 cc. Volume, complete with collar and base plate. Rammer 2. 6 kg x 310 mm controlled fall.
• Instrument consists one each of : Compaction Mold, gun metal/ M.S., 150 mm ID X 127. 3 mm height volume 2250cc. complete with collar and base plate. Rammer 4. 89 kg x 450 mm controlled fall for heavy compaction test according to IS 2720 (Part - VIII).
• Note: instead of gun-metal molds, steel molds are also available.

Product Details:

USEFUL TODETERMINE SPECIFIC GRAVITY OF CLAYS, SAND AND GRAVEL OF SIZE SMALLER THAN10MM. SPECIFICATION : COMPRISES A 1 KG. GLASS JAR WITH BRASS CONE. LOCKINGRING AND RUBBER SEAL.

Product Details:

The Sieve Shakers is used to make the process of sieving easier and quicker. The sieve shaker effects a more elaborate and standardized sieving action to produce accurate results and eliminate personal errors involved in manual sieving. The sieve shaker equipment can carry upto 8 sieves. The shaker produces the gyratory as well as the tapping motion.

Product Details:

The Digital Compression Testing Machine has been designed to meet the need for a simple, economic and reliable means to test concrete for its compressive strength. The design expressive of simplicity, both of construction and operation, makes the machine easy to use and maintain. The unit is compact, making it useful for site and Laboratory applications. The digital machines are provided with a pace rate controller, to enable maintain a constant of loading.

Features:

• High stability four column load frame digital

• Each frame tested for stability and alignment to avoid tension failure during a test and to ensure centre loading
• Standard Platens for 3 X 6"/ 4 X 8" and 6 X 12" cylinders included.
• A precise large diameter spherical upper platen for optimum results
• Variety of optional accessories for cubes, blocks, bricks and flexure test available
• Motorized hydraulic power pack or pumping unit with a rapid approach and automatic overload protection
• Comes standard with safety Guards on all four sides.
  
  

The Complete unit comprises a Loading Unit which is of fully welded or two pillar model construction having a cross-head with a spherical seated platen. The lower platen is attached to the top of the piston. The Loading capacity is of 2000 KN, Cubes up to 200 mm & Cylinders up to 150 mm Dia X 300 mm Height can be tested using the appropriate spacers.

Product Details:

Often, existing Concrete Test Hammer structures will need to be examined and tested to ensure the concrete remains of adequate strength and durability. Rebound hammer surveys can be conducted to provide a rough estimate of concrete strength, where it is not possible to determine this by more accurate means such as core extraction and testing. The test involves using a special rebound hammer, which measures the recoil of a piston against the concrete surface when a standard force is applied. This recoil can then be correlated approximately to concrete strength.

Features:

• Long working life
• Highly durable
• Less maintenance
  
  

General Descriptions & Specifications:
The rebound hammer consists of a barrel in which is housed a hammer mass attached to an impact spring which slides on a guide bar. A plunger is attached to the guide bar which is pressed against the surface to be tested. As the piston is pressed against the surface to be tested, on reaching the compressive strength, the hammer mass is released and rebounds to a certain extent, according to the strength of the surface, which is indicated by a rider on a calibrated scale. A lock button fixed on the body of the hammer lock the rider in place and the rider can be reset to zero Position by using the same button. The equivalent compressive strength can be computed from the chart supplied. It is suitable for a specimen of compressive strengths 100-700Kg/cm. The instrument, complete with a grinding stone for polishing the test surface, is supplied in a carrying case.

Product Details:

Concrete Permeability Apparatus: Recognized for its quality and optimum performance, this apparatus provides accurate as well as reliable results.

 

Features:

• Less maintenance
• User friendly
• Resists the flow of water

 

Equipment consists of:

• A control panel with three independent control circuits
• Three permeability cells for 150mm diameter specimens
• Three glass/plastic bottles to gather the percolated water

Product Details:

Pozzolana Cement Mortar Permeability Apparatus:
For water proofing of concrete, admixture and special water proof cements are used. Water Proofing of these compounds, is established by measuring permeability of standard mortar. Permeability apparatus is used to determine permeability to water of cement mortar specimen with or without water proofing compound.

The Mortar Permeability Apparatus comprises brass / Gun Metal Cells mounted on a stand and a pressure chamber with a pressure regulator. The cell can accommodate 100mm Dia x 50mm High Specimen. Each Cell assembly consists of one base plate. The base plate has one outlet for water and recessed to hold the specimen in place with ring washer in between. The top plate has an inlet for water and a suitable connector for the application of pressurized water in the cell. The mould and collar are clamped between the base plate and the top plate with the help of four tension rods and nuts. The cells are mounted on a stand. The pressure chamber is fitted with a pressure regulator, which helps in regulating the pressure from 0-7kg/cm². The regulator has two pressure gauges, one for indicating the pressure in the chamber (0-10.5kg/cm².) and the other for indicating the testing pressure (0-7kg/cm².). The Pressure Chamber is connected to the cells with pressure hoses and with couplings. This pressure chamber is fitted with Schrader valve.

 

Accessories:

Product Details:

California Bearing Ratio Test Field Type:

To know C. B. R. Values in situ, it is useful in determining the load carrying capacity in the field when in-place density and water contents are such that the degree of saturation is 80 % or greater, when material is cohesionless and coarse-grained, such that it is not effected by changes in water contents and when the material has been in-place for considerable time. The loading is effected by means of a mechanical load frames which can be fixed to the under side of a truck.

 

Accessories : Dial gauge 0.01mm x 25mm. High sensitivity Proving Ring 5000kg. capacity with calibration chart and carrying case.

Product Details:

The Sand Pouring Cylinder is used for determination of the dry density of compact, fine, medium grained soils and for layers not exceeding 50cm thickness. A circular hole is dug into the ground, all the soil from within it collected, weighed and dried and the whole back filled with a standard uniform sand or fine gravel poured from a calibrated container for calculating the volume of the hole. The complete apparatus consists of a Sand Pouring Cylinder fitted with Conical funnel and Shutter, Cylindrical Calibration Container, and a Metal tray with a central hole.

Product Details:

Plastic Limit Set: Moisture contents at which soil has smallest plasticity is called limit. For determination purpose plastic limit is defined as the water content at which a soil will just begin to crumble when rolled in to a thread of 3mm dia.

Product Details:

We are pioneers in offering patrons with a huge assortment of Sand Equivalent Test Apparatus at market leading prices. Manufactured with precision, this range is accredited in various sectors of the industry to function as per patrons needs and demands. This range is available with us in various sizes, grades and other detailed specifications as per patrons needs and demands. Moreover, a customized range can also be availed from us that suits patrons needs and specifications.

 

Features:

• Compact design
• Sturdy construction
• Available in standard sizes
• Available in wooden boxes
• Abrasion resistant

Product Details:

Penetrometer Apparatus is used for penetration test on a wide variety of materials. It consists of a head Support mounted on a vertical rod which can be adjusted for height.A rack and pinion and pointer assembly provides fine adjustment of needle tip to Sample and in Corporates a Slipping clutch mechanism which make reading of penetration and subsequent resetting a sample and accurate operation. The dial graduate from 0-400 in one tenth millimeter Sub Division. The Instrument is supplied with two sample containers & 2 Watts.

Additional Information:

• Delivery Time: 2-3 weeks

Product Details:

Our clients can avail Cylindrical Moulds in various sizes at leading market prices

• Cylindrical Moulds available in sizes of 150mm dia. x 300mm high
• Cylindrical Moulds available in sizes of 100mm dia. x 200mm high
• Cylindrical Moulds available in sizes of 300mm dia. X 600mm high.

Product Details:

Curing Tank: The strength of concrete is generally estimated after 28 days by crushing field test cubes or cylinders made from the representative concrete used for the structure. The utility of ascertaining strength after 28 days is often questioned since by this time considerable concrete would have been placed and work may have progressed. It is then rather too late for remedial measures. It is therefore of tremendous advantage to predict 28 days strength within a few hours of casting the concrete so that, we have a good idea about the strength of the concrete.

The rate of gain of strength of concrete depends on the reaction rate of cement and additions with water (Hydration). In common with all chemical reactions, the rate of reaction depends on the reaction of temp. Higher reaction temperature gives a higher rate of reaction e.g. the concrete gains strength more rapidly when its temp. is higher. Accelerated curing is the process by which the temperature of the concrete is raised artificially by applying external heat to speed up the rate of gain in strength.

The test method covers procedures for curing test specimens of concrete stored under conditions intended to accelerate the development of strength. The procedures are: Procedure A- Warm Water Method, Procedure B-Boiling Water Method
Specifications:

• Accelerated Curing Tank having the capacity to accommodate 6/12/18 Concrete Cubes of 150mm size with a facility for accelerated curing by Boiling water method up to temperature range: 100 +/- 2 deg.C as per IS standard IS: 9013. Also it will have capacity for curing by warm water method at temperature 55 +/- 2 deg.C
• The tank will consist of a rectangular double walled metal cabinet, inside lined with stainless steel, outer powder coated. Easily replaceable high Wattage heaters are mounted inside the chamber. A slow speed stirrer is provided to circulate water inside the chamber to maintain the uniform temperature of water. A strong stainless steel perforated platform is provided for keeping the cubes and also have a lid with lifting handle to cover the chamber.
• The temperature is indicated and controlled by a DIGITAL auto tuning PID Temp. Controller with soak timer to control the duration of heating and then to shut down the system without manual attendance. The front panel will have power supply indicating lamp, control action indication lamp, and one main switch. Suitable for operation on 220 V, 50 Hz single phase, AC supply or 440 V 50 Hz, 3 phase AC supply, for a bigger size of curing tank.

Product Details:

Gauging Trowel we offered trowel manufactured using a high grade carbon steel blade and the latest technology by adroit professionals. Used in agricultural and construction sectors to pick sand, this trowel is available in variegated sizes and specifications. Apart from this, customers can avail this trowel from us at market leading prices.

Features:

• Soft grip handle
• High strength
• Rust free

Product Details:

Keeping our synchronization with the development taking place in this industry, we are engrossed in delivering a broad range of Gillmore Needle Apparatus.

 

Features:

It is used for the determination of time stetting of hydraulic cement. Gillmore needle apparatus is provided with a base with two horizontal arms and vertical shaft.

A base with a Vertical shaft and Two horizontal arms. The lower arms are adjustable for height 1 no. Initial needle 1/12-inch dia ¼ lb. Wt. 1 no. Final needle 1/24 inch dia. ¼ lb. Wt. 1 no. Glass base plate. Complete as above

Product Details:

As per the needs and requirements of our clients, we are involved in providing Manual Hydraulic Jack.

Product Details:

Jolting Apparatus: For making standard rectangular specimens of 40 x 40 x 160mm. Of port land and pozzolana cement mortar for determining the transverse strength.

 

Salient Features:

• The jolting apparatus consists of a rectangular table rigidly connected by two support arms to a spindle at a horizontal distance of 800mm from the centre of the table. There is a projecting lug with a plane face on the lower face of the table beneath which is a stop with a rounded upper surface. The table can be raised and allowed to fall freely on the stop by a cam which is connected to a motor and gear box through a V-belt and pulleys. The cam rotates at a rate of 60 rev./min. A stroke counter fitted with micro-switch is provided which stops the machine after 60 jolts. Locating pins are provided for mounting the mould compartments on the table. The mould surmounted by the hopper can be clamped rigidly to the table. Supplied complete with mould and hopper. Suitable for operation on 230 Volts, single phase. A.C.supply.
  
  Spares and Accessories:

1. Steel mould with a base plate having three compartments each having 40mm x 40mm x 160mm. internal dimensions.
2. Apparatus for demoulding the specimen.

Product Details:

Three Cell Model It comprises of three test units mounted on a single frame. Each unit consists of - a loading frame having capacity of 20 kg/cm² with a loading yoke and lever arm complete with counter balancing adjustments. A fixed ring consolidation cell for a 60mm dia. x 20mm thick specimen, complete with two porous stones, pressure pad (perforated), cutting ring and water reservoir with tubing and connector is provided. A set of weights is provided to give a stress of 10 kg/cm² on a 60mm dia. specimen, comprising: 7 nos. 0.05 kg/cm2, 5 nos. 0.1kg/cm2, 6 nos. 0.2kg/cm2.,6 nos. 0.5kg/cm2., 5nos. 1.0kg/cm2

Product Details:

Core Cutter is used for determination of in situ dry density of natural or compacted fine-grained soil, free from aggregates. A cylindrical cutter is used to extract a sample of the soil with the help of a dolly and rammer. From the weight, density and the moisture, and dry density of the soil is readily calculated. I t consists one each of cylindrical core cutter mode of steel, 127.3mm. Long and100mm internal diameter. Steel dolly, 25mm high with a lip to enable it to be located on top of the core cutter, rammer with a detachable steel rod.

Product Details:

Extractor Frame (Universal) Comprises of a frame designed for screw jack operation, one each of the adaptor plates and plunger adaptors for 38mm, 75mm, diameter, 100mm diameter, 150mm diameter, Extractor Frame (Universal) for Civil Engineering from Laboratory Equipment Manufacturers India - specimens and a stand to obtain simultaneously three 38mm diameter samples from one 100mm diameter sample. The adaptor plate which slides a long the slotted supports can be clamped at any desired position by means of locking nuts. Besides this, the tube or mould can be held in position by raising the tube guides and held in position with locking screws. the lead screw movement can be stopped at any predetermined position by tightening the lead screw locking collar. Plunger adaptor for 200mm dia samples. Adaptor plate with 200mm dia hole and device to extract 3 number 38mm dia samples

Product Details:

Plate Bearing Test Apparatus

Technical Details:

• The basic outfit consists of: 50 Tones Hydraulic jack with separate pumping unit fixed to it a 0-500 KN. x 0.5 KN.
• Pressure gauge and flexible metal pipe 5mtr. long - 1 No. Special ball and socket arrangement between the jack and the bearing plate - 1 No. Extension rod 12mm. dia x 25cm long for taking dial gauge readings - 16 Nos.
• Magnetic base with female thread on top for holding extension rod - 4 Nos.
• Top end plate, 50mm, dia with male thread for fitting onto the extension rods and positioning the dial gauge plunger - 4 Nos.
• Column 15cm dia x 25cm long with flanges complete with four bolts and nuts - 2 Nos.
• Column 15cm x 50cm long with flanges complete with four bolts and nuts - 1 Nos. Bridge support of welded steel angle construction, 5 mtr.
• Span and stands approximately 30cm, high, fitted with two quick release clamps after positioning and holding the dial bracket - 2 Nos.
• Plate 60 cms x 60cms sq. x 25mm thick Plane
• M.S.Plate 45cms x 45cm.sq. x 25mm thick Plane
• M.S. Plate 30cms x 30cm.sq. x 25mm thick
• Dial Gauge 0.01mm x 25mm - 4 Nos.

Product Details:

Specifications :

• Suitable for calibration of Cube testing machines, Universal testing machines etc
• Capacity: Available in different capacities ranging from 500N to 3000kN

Product Details:

Rock Cutting Machine: Rock / Concrete / Masonry, saw cutting machine can be used to cut Rock Cores. Concrete Cores, Stones, Building materials and metallic specimens. A smooth finish cut can be made with the machine in either wet or dry operation according to the nature of specimen (Cutter are at extra cost). The specimen cutting machine is designed to cut up to 200 mm (specify the size of deep cut required in the specimen) deep cut in the Concrete, Stones, Tiles, Soft rocks and Hard rocks or any other similar material. Specimen cutting machine is supplied complete fitted on a steel table, vice is fitted to hold the specimen. A guard is provided for the Diamond cutting wheel. The machine is operated by an enclosed type of fan cooled motor through the geared head drive. The speed of the cutting wheel is approximate 2100 to 2200 r.p.m. or in accordance with the revolution specified on the particular cutting wheel. The machine is fitted with a water supply pump for cooling the specimen and cutting during a cutting operation. The machine is suitable for operation on 440 Volts A.C. mains, 3 phases. In the machine, an arrangement is provided to move the sample, fitted on vice, lengthwise and breadth wise.

Product Details:

Sampling Outfit : Undisturbed samples of soil at different depths can be collected using these sampling tubes. The kit includes all necessary implements for boring, collection and sealing with wax. The operation may be carried out either using a tripod stand or without it. The equipment is supplied in a canvas carrying bag.

 

Salient Features:

• For preparing 38 mm dia Soil Specimen.
• The outfit comprises: Sample Extractor, Screw type with a wire sample Timmer. Split Mould, 38 mm dia x 76 mm long. Split mould, 38 mm inch dia x 88 mm inch long (in two parts) can be fitted to the screw type extractor enabiling salt specimens to be prepared ready for unconfined compression test. They are fitted with quick release system. Sampling tube 38 mm dia x 150 mm long. Sampling Tube 38 mm dia x 200 mm long. Jarring link for driving the Sampling Tube. Adaptor with locking screw for fitting the sampling tube to jarring link.

Product Details:

Sand Equivalent Shaker: The unit provides a constant uniform shaking with automatic cycle test. Oscillating excursion is 200 mm at 175 strokes / minute rate. Complete with timer that automatically stops the shaker at the end of the test. Power Supply 230 V A.C. 50Hz.

Product Details:

Available with us is a compact range of Soil Hydrometer, which can be further availed in diverse sizes, grades and other dimensions suiting patrons needs and specifications. In addition to this, our range is manufactured by making use of optimum grade raw material to obtain maximum level of patron satisfaction. A precision designed range, this product is quality tested before dispatch to offer a defect free range that can also be availed in customization options as per the customers requirements.

 

Some features are:

• Scratch resistance
• Light Weight
• Durable
• Rust resistance
• Accurate dimensions

Product Details:

We manufacture a wide range of Air Entertainment Meter in compliance with IS:1199. These are customized as per the specifications of our clients and are fabricated while using high grade raw material. Appreciated for high quality features such as long performance, optimum serviceability and corrosion resistance, these meters possess following parts:

• Pressure tight flanged bowl for max size of aggregate 38mm. 0.005 cub mt
• Bowl is fitted with a removable flanged conical cover assembly
• Instrument supplied with cylinder with spring clamp, Trowel, Tamping rod, Straight edge, Rubber mallet & measure

Product Details:

Specification:

• The machine consists of a motorized load frame. The lower platen has two rollers, the distance between which is adjustable. For 150 mm x 150 mm x 700 mm beam, the centre distance between the rollers is 600 mm, while it is 400 mm for beams of size 100 mm x 100 mm x 500 mm. The upper platen has also a pair of rollers whose distance adjustable. It is 200 mm centre to centre, for 150 mm x 150 mm x 700 mm size beam and 133 mm for 100 mm x 100 mm x 500 mm size beam. Total capacity of the machine is 100 KN. 150mm dia pressure gauge of 0-100 KN x 1 KN least count to indicate load is fixed on the load frame.
• A separate electrically cum hand operated pumping unit housed in a cabinet is supplied. On/Off switch and a slow/fast lever to control the rate of loading are fitted on the front panel of the pumping unit. A facility for hand operation is provided. A micro switch and relay fitted inside the pressure gauge protect the unit from over loading.
• Hand operated version consists of a load frame. A small hand pumping unit is attached to the load frame. Since this is a hand operated light weight machine. It is useful for field laboratory also.

Product Details:

Laboratory Cement Autoclave with Stainless Steel Chamber 21 Kg/cm.The Portable Autoclave is suitable for conducting accelerated soundness tests on cement or the autoclave expansion test requiring constant steam pressure with the correspondent It consists of a stainless steel cylinder with a welded heat insulated over, mounted on a sturdy supporting frame, enclosed in a heat insulated metal housing, attractively finished. The attached control unit encloses a sensitive pressure regulator and pressure gauge, power switches and pilot lights for controlling the electric heating units. Inside Chamber Dimensions- 10.5 cm diameter x 40.5 cm height suitable for operation on 230 V, 50 Hz, Single Phase, AC supply. Supplied complete with Test bar holder, special rack to hold specimens above the water level in the autoclave and in a vertical position to expose them in the same manner. Note: Ordinary Laboratory Cement Autoclave with Mild Steel Chambers are also available.

Product Details:

STANDARDS:IS 4031 1968, ASTM C 188

SPECIFICATION:

USED FOR FINDING SPECIFIC GRAVITY OF HYDRAULIC CEMENT. MADE FROM BOROSILICATE GLASS. THE FLASK IS 243MM IN TOTAL HEIGHT, HAVING A BULB OF 90MM DIA OF 250ML APPROXIMATE CAPACITY. THE LONG NECK OF THE FLASK HAS AT TOP A FUNNEL OF 50MM DIA IN THAT FITS A GROUND GLASS STOPPER.

THE NECK HAS OVER-ALL 11MM I.D. UPPER PORTION IS GRADUATED FROM 18ML TO 24ML WITH 1 ML GRADUATION. JUST AT THE BOTTOM OF THE NECK 1 ML CAPACITY IS MARKED IN BETWEEN THERE IS 17 ML CAPACITY BULB.

Product Details:

Grain Size Analysis (Pipette Method) : As per IS 2720 (PART IV) AND BS 1377:2. This is for the determination of the sub sieve particle distribution in a soil sample by mechanical analysis. An analysis of this kind expresses quantity the proportions by weight of the various sizes of particles present in the soil. It is recommended as a standard procedure to use dispersion agent to avoid flocculation. The apparatus consists of a sliding panel which moves up and down by means of a screw allowing Anderson pipette fixed to it to be raised or lowered vertically. A sedimentation tube is held by a laboratory clamp provided on the stand below the pipette. The depth of immersion is measured by a scale graduated in mm at the side of the sliding panel. Supplied complete with Anderson pipette 10ml. At the side capacity made from glass, and a sedimentation tube also of a glass of 500ml capacity and 50nos. Test form pads.

Accessories at Extra Cost:

• Sedimentation Pipette (Anderson pipette) 25ml.
• Sedimentation tube 100ml
• Sedimentation pipette 10ml
• Sedimentation tube 500ml

Product Details:

Point Load Index Tester, a rock testing instrument for determining the Diametrical Point Load Strength Index of rock cores and Irregular Lumps which may be tested without any treatment. The Point Load Test is primarily as index Test for strength classified of rock materials. This instrument is mainly intended for field measurements on rocks specimen, but it can be used in the laboratory. The results of the test may also be used to predict the uniaxial compressive strength of rock from correlations. The apparatus is light and portable and can be used in the laboratory as well as in the field.

Features :

• Equipment is light and portable
• Rock core specimens can be tested without any preparation
• The instrument can be used in the laboratory as well as at the drilling site
• The results of the test may also be used to predict the uniaxial compressive strength of the rock.
• With this instrument, a wide range of core size can be tested
• The frame has adequate adjustments to align perfectly the loading axis passing through the centre of the bearing plates and loading platens at the position of the ram of the hydraulic jack.

Product Details:

The Blain Air Permeability Apparatus is used to determine the fineness of Portland cement in terms of the specific surface expressed as total surface area in square centimeters per gram of cement. Blain Air Permeability Apparatus for Civil Engineering from Laboratory Equipment Manufacturers India - The Blaine apparatus draws a defined volume of air through a prepared bed of cement of defined porosity.

 

The apparatus comprises one each of Brass or stainless steel permeability cell 12.5mm,’U’ tube manometer with stop cock mounted on a laminated wooden stand, perforated metal disc, plunger, Rubber stopper, Rubber tube – 30cm long with rubber bulb.

Product Details:

Lateral Extensometer is used for determining the lateral extension of 15cms dia x 30cm high cement concrete cylinders while testing them under compression.

 

Features:

• The unit consists of two movable frames pivoted at one end. The extensometer is fixed to the specimen with the help of tightening screws. The lateral extension is indicated on a dial gauge of 0.002mm x 12mm travel. The extension is magnified 2.5 times and the dial gauge readings are to be divided by 2.5 to get the exact readings.
• A spacer strip is provided to initially set the dial gauge, and can be removed after initial setting. Supplied in a wooden carrying case.

Product Details:

Sand Absorption Cone & Tamper: Used for determining the slump of fine aggregate in the determination of bulk and apparent specific gravity and absorption of fine aggregate.

Product Details:

Being a quality based firm, we are offering a quality assured assortment of Standard Spatula. The Standard Spatula we offer is widely demanded amongst the clients for its sturdiness and reliability. Moreover, these products are known for their safe use

Product Details:

High Speed Stirrer: This is for mechanical analysis and also other laboratory applications for stirring. Speed approximate 4000rpm under load. A dispersion cup is supported on a rest on the stand of the stirrer and has a removable baffle. for operation on 230-250 volts A.C.supplied without dispersion cup or baffle.

Product Details:

Four standard sizes of Cube Mould are offered and supplied complete with the base plate.

Specification:

• Cube Mould Size 15x15x15 cm
• Cube Mould Size 10x10x10 cm
• Cube Mould Size 7.6x7.6x7.6 cm

Product Details:

Two standard sizes of Beam Moulds are offered for casting concrete specimens for flexural strength testing. These beam moulds are made of cast iron and are supplied complete with a base plate.

 

Specifications:

• Material S50 C
• Demoulding Automatic
• Mould Life <300000 shots
• Colour Blue

Type of Mould

Product Details:

Slump Test Apparatus: Our commitment and strict adherence to customer satisfaction have given us repeat business. Our range of Slump Cone Apparatus is stringently tested on different quality parameters. We regularly upgrade our processing techniques to deliver the best quality products to our valuable clients at industry leading pricing. Our offered range of Slump Cone Apparatus is developed at pioneering production unit as per the market quality standards. Our organization is committed for the time bound delivery at any part of the country.

Features:

• Reasonable prices
• Precise engineering
• Quality assured

Product Details:

Length Comparator:

The apparatus can be used for three basic tests:

• Initial drying shrinkage: The difference between the length of the cured specimen and the length when it is dried.
• Drying shrinkage: The difference between the length of the specimen from the existing structure and its length when completely dried.
• Moisture movement: The difference between the length of the dried specimen and its length when again saturated with water.
• The apparatus consists of a frame with an adjustable cross head. Length Comparator for Civil Engineering from Laboratory Equipment Manufacturers India - The base is provided with a stainless steel circular platen having a recessed seating and a 300 to 301 mm long alloy steel reference bar having coefficient of thermal expansion less than 2 x 10-6 mm/degC with 6 mm dia steel balls mounted at the ends, Supplied complete, with a dial gauge 0.002 mm x 10 mm

Product Details:

Product DescriptionWe have carved a niche amongst trusted companies for offering a broad range of Concrete Needle Vibrator.This Needle Vibrator is available according to the specific demands of our client’s requirements.

Product Details:

Laboratory Concrete Mixer: Concrete mixer laboratory type, electrically operated. Designed to remove the burden, some work of hand mixing. Uniform thoroughly mixed batches can be produced. The counterbalanced drum is easy to tilt 1. 1/2 to 2cu.ft.mix. The total drum volume is however 3cu.ft. Mounted on a sturdy rubber tyre stand, and the drum is mounted for end discharge and equipped with end towing pole. Equipped with 1/2H.p. electric motor. Suitable for operation on 220/230 volts A.C. single phase. This multi flow mixer absorbs few air during mixing, requires shorter mixing time and grants a perfect homogeneity in mixtures having a low water and cement ratio. The pan is easily removable by means of a trolley. The blades are hardened against wear.

Product Details:

Dames And Moore Sampler:
Highly useful for sampling soils. The sample collects into rings inside the sampler. These rings along with the specimen can be directly placed in a consolidometer cell assembly, thereby reducing the number of operations to extract the sample from a sampler, trimming to size and transferring into the ring etc. The possible disturbance in these operations is eliminated.

Spares:

• Body consisting of split pipe threaded at both the ends and Shoe
• Head Assembly: Set of 10 rings 60mm O.D. and 25.4mm long

Product Details:

We are specialized in offering Plastic Cube Mould Avaliable in Various Sizes
to our customers. Our presented product is extremely used in the market owing to their top features.

Product Details:

Augers are used to collect disturbed soil samples at reasonable depths for laboratory tests. Augers are available in two types and each in different sizes. Blade type (posthole type) and helical type (screw type). Each auger outfit consists one each of auger head, one meter long rod, tee piece and handle. Depth of excavating can be increased using additional extension rods.